buttons simultaneously.
telephone number in the warranty.
your component.
button.
channel and volume control.
(not supplied).
battery compartment.
Press the S (Set) button.
search for another code.
numbers. Works in the same
or VCR鈥檚 commander.
Fastext buttons.
To play.
To stop.
To rewind.
To fast-forward.
z.
To change the input mode.
supplied to the TV.
To switch to Teletext.
display.
display.
To change the programme.
Also to turn on the power.
between 20 and 29.
To turn on.
To return from Teletext to TV.
mode.
To enter the selection.
鈥?/div>
ql
To operate
JUMP, FLASHBACK
or
CHANNEL RETURN
function
on the TV depending on the
setting of the TV鈥檚
manufacturer.
Press the button of the component that you want to set up.
Note
Be sure to proceed to each next step in the above procedure within 10 seconds;
otherwise setting mode will be canceled.
1
2
Setting Another TV, VCR, DVD,or Satellite Tuner
3
Enter the three-digit component code in the 鈥淐omponent
Code Numbers鈥?table.
For example, to set a Philips鈥?TV, press
-86.
When you have two or more components of the same type (for
example, three VCRs), you can change the component鈥檚 type on
DVD
button and
SAT
button.
When to replace the batteries
Under normal conditions, batteries will last up to six months. If the
Remote Commander does not operate properly, the batteries might
be worn out. Replace the batteries with new ones.
Notes
鈥?Replace both batteries with new ones.
鈥?Do not take more than 20 minutes to replace the batteries; otherwise, your
setting of the code numbers will be erased.
1
2
3
4
4
Press the
t
button.
Press the
S
(Set) button.
Press the
DVD
or
SAT
button.
Press the
x
button.
Press one of the following buttons;
-
to set up a DVD
1
to set up a VCR
3
to set up a satellite tuner
8
to set up a TV
Press the
t
button.
Enter the component鈥檚 code number by following steps 1 to 5 of
鈥淪etting by Entering the Code Number鈥? or steps 2 to 7 of
鈥淪etting by Searching for the Correct Code鈥?
5
Aim this Commander to your component and check if you can
operate it using this Commander.
5
6
Specifications
Operating a Satellite Tuner
3
To select double-digit
numbers.Work in the same way
as your satellite tuner鈥檚
commander.
4
N, x, m, M
:
Fastext buttons.
X:
To show or hide the EPG
display.
6
To switch the output of the
satellite receiver to the TV.
(When you connect a TV cable
or antenna to the receiver, the
output switches between a TV
and SAT program.)
7
To switch to Teletext.
9
To call up the MENU display.
qd
and
qf
To change the programme.
qg
To bring up the Master Guide.
qh
To exit the mode.
qj
To select the channel that鈥檚
highlighted. To bring up the
Station Index when a program
guide is not displayed.
qk
Programme up:
+
Programme down:
鈥?/div>
ql
To operate
JUMP, FLASHBACK
or
CHANNEL RETURN
function
on the satellite tuner,
depending on the
manufacturer鈥檚 setting.
Operable distance
Notes on Batteries
鈥?Do not mix old batteries with new ones or mix different types of
batteries together.
鈥?If the electrolyte inside the battery should leak, wipe the
contaminated area of the battery compartment with a cloth and
replace the old batteries with new ones. To prevent the electrolyte
from leaking, remove the batteries when you plan not to use the
Commander for a long period of time.
Go through the same procedure for each component you want to set
up.
Approx. 7 m (23 ft) (varies depending on the component of each
manufacturer)
Power requirements
Two R6 (size AA) batteries (not supplied)
Battery life
If you cannot operate your component...
鈥?First, try repeating these set up procedures using the other codes
listed for your component (see 鈥淐omponent Code Numbers鈥?.
鈥?If 鈥?after trying all the codes listed for your component 鈥?you still
cannot get the Commander to work properly, try the search
method described under 鈥淪etting by Searching for the Correct
Code鈥?
Notes
鈥?Be sure to proceed to each next step in the above procedure within 10
seconds; otherwise, the setting mode will be canceled.
鈥?You cannot set up more than one component at a time on each component
select buttons. If you want to set up two or more same components of
different brands, see 鈥淪etting Another TV, VCR, DVD, or Satellite Tuner鈥?
Operating a Component
1
Press the button of the desired component on the
Commander.
Approx. 6 months (varies depending on frequency of use)
Dimensions
Mass
Approx. 51.8
脳
195
脳
31 mm (w/h/d) (2
1
/
8
脳
7
3
/
4
脳
1
1
/
4
in.)
Approx. 100 g (3.5 oz.) (not including batteries)
Design and specifications are subject to change without notice.
2
Point the Commander directly to your component and press
the button for the desired function.
See 鈥淩emote Button Descriptions鈥?for details.
Notes on using the Commander
鈥?Using this Commander will not add new functions to your components. The
functions of the Commander are limited to the functions of the component
itself. For example, if your TV does not have a mute function, the
%
button
on this Commander will not function with your TV.
鈥?Do not forcibly remove or tear off the corner protector.
Tip
You can write down the code number on the label inside the battery
compartment lid.
1
2
