0.015鈩?/div>
0.020鈩?to 1.00K
*
36 Watts
*
54 Watts
*
60 Watts
*
18 Watts
60 A
rms
60 A
rms
60 A
rms
Current
Limited
Current
Limited
Current
Limited
Film (
J
) to Case (
C
)
6.94擄C/Watt
3.47擄C/Watt
2.31擄C/Watt
2.08擄C/Watt
I=
P/ R
250 V
rms
These products are covered by one or more
patents, also patents pending.
Derating Curve
RATED POWER %
Speci鏗乧ations:
Temperature Coef鏗乧ient:
TC referenced to +25擄C,
螖R
taken at +150擄C
0.50 ohm and above, -20 to +80 ppm/擄C
0.050 ohm to 0.49 ohm, 0 to +100 ppm/擄C
0.015 ohm to 0.049 ohm, 0 to +200 ppm/擄C
0.005 ohm to 0.014 ohm, 0 to +300 ppm/擄C
Operating Temperature:
-55擄C to +150擄C
Inductance:
10 nH typical in series when
measured at the shoulder of the lead.
Capacitance:
<1 pf typical without heat sink.
DWV:
1500 V
rms
AC isolation to the mounting
surface or a clip in contact with the top surface.
Insulation Resistance:
10,000 Megohms, min.
The resistor element is electrically isolated from the
mounting surface.
Momentary Overload:
1.5 times rated power for
5 seconds,
螖R
鹵(0.5 percent + 0.0005 ohm) max.
Load Stability:
2000 hours at rated power
螖R
less than 鹵(1 percent +0.0005 ohm).
Moisture Resistance:
Mil-Std-202, Method 106,
螖R
鹵(0.5 percent + 0.0005 ohm) max.
Thermal Shock:
Mil-Std-202, Method 107,
Cond. F,
螖R
鹵(0.5 percent + 0.0005 ohm) max.
Shock:
100G, Mil-Std-202, Method 213,
Cond. I,
螖R
鹵(0.4 percent + 0.0005 ohm) max.
Vibration, High Frequency:
Mil-Std 202,
Method 204, Condition D,
螖R
鹵(0.4 percent
+ 0.0005 ohm) max.
Terminal Strength:
Mil-Std-202, Method 211,
Cond. A (Pull Test) 5 lbs.,
螖R
鹵(0.2 percent
+ 0.0005 ohm) max.
Terminal Material:
Solderable
Measurement Note:
Resistance measurements
shall be made at 0.2 inch (5.08 mm) from the
resistor body.
Sales and Corporate Of鏗乧e
1717 Chicago Avenue
Riverside, California 92507-2364
Phone: (951) 788-1700
Fax: (951) 369-1151
28_IL128.1004
100
80
60
40
20
0
25
100
CASE TEMPERATURE,
擄C
150
*
Derating Using Case Temperature (TC):
All power and associated overload ratings are
derated based upon case temperature using the
derating curve. The case temperature is mea-
sured at the center of the ceramic mounting sur-
face, with the part properly mounted and under
electrical load. Without a heat sink, when in free
air at +25擄C, the MP2060 is rated for 2.5 watts.
The thermal design should satisfy the following equation:
Case Temperature (Tc) + [Thermal Resistance (R
胃JC
) x power applied (Watts)] 鈮?150擄C, considering the full
operating temperature range of the application.
Mounting Note:
Mount on a smooth, clean and 鏗俛t heat sink surface with a thermal interface material, such as
thermal grease. The entire exposed ceramic portion must be in contact with the heat sink. When using a
spring clip, it is recommended that a mounting force of 8 to 30 pounds (35 to 130 N) be applied to the center of
the package. The clip should be round or smooth in the contact area to avoid concentrating the load on a small
point of the plastic body of the package. Another mounting option is to use a pressure bar method which can
achieve a greater mounting force with a greater contact area.
For additional applications information regarding mounting and pulse handling see the Caddock Ap-
plications Notes at caddock.com or contact Applications Engineering.
0.410
鹵
0.010
(10.41
鹵
0.26)
0.175
鹵
0.010
(4.45
鹵
0.26)
Standard Resistance Values:
Tolerance: 1% Standard (except as noted)
0.33
惟
0.40
惟
0.50
惟
0.75
惟
1.00
惟
1.50
惟
2.00
惟
2.50
惟
3.00
惟
3.30
惟
4.00
惟
5.00
惟
7.50
惟
8.00
惟
10.0
惟
12.0
惟
15.0
惟
20.0
惟
25.0
惟
27.0
惟
30.0
惟
33.0
惟
40.0
惟
47.0
惟
50.0
惟
56.0
惟
75.0
惟
0.005
惟
5%
0.010
惟
2%
0.015
惟
2%
0.020
惟
0.025
惟
0.030
惟
0.033
惟
0.040
惟
0.050
惟
0.075
惟
0.10
惟
0.15
惟
0.20
惟
0.25
惟
0.30
惟
100
惟
120
惟
150
惟
200
惟
250
惟
300
惟
330
惟
400
惟
470
惟
500
惟
560
惟
750
惟
1.00 K
0.150
鹵
0.030
(3.81
鹵
0.76)
MP2060
50.0
1%
0.100
鹵
0.020
(2.54
鹵
0.51)
0.640
鹵
0.010
(16.26
鹵
0.26)
0.500
鹵
0.050
(12.70
鹵
1.27)
0.050
鹵
0.007
(1.27
鹵
0.18)
0.200
鹵
0.010
(5.08
鹵
0.26)
DIMENSIONS IN INCHES AND (MILLIMETERS)
0.035
鹵
0.007
(0.89
鹵
0.18)
0.105
鹵
0.010
(2.67
鹵
0.26)
Ordering Information:
Model Number:
For custom values and tolerances contact
Applications Engineering
Tolerance
MP2060 - 0.050 - 1%
Resistor Value:
Packaging Information:
MP2060 resistors are packaged in plastic shipping tubes, 50 pieces
per tube. These resistors are available in a 50 piece minimum quantity and in full tube
quantity increments (i.e. 50, 100, 150, etc.).
Applications Engineering
17271 North Umpqua Hwy.
Roseburg, Oregon 97470-9422
Phone: (541) 496-0700
Fax: (541) 496-0408
漏 2004 Caddock Electronics, Inc.
CADDOCK
e-mail: caddock@caddock.com 鈥?web: www.caddock.com
For Caddock Distributors listed by country see caddock.com/contact/dist.html
1
