鈥?/div>
Open collector output
Absolute Maximum Ratings
(No derating required up to 70
o
C)
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55
o
C to +150
o
C
Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55
o
C to +125
o
C
Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 10 seconds) . 260
o
C
Average Input Current - I
F
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 mA
(1)
Peak Output Current - I
F
(50% duty cycle, 1 ms pulse width) . . . . . . . . . . . . 50 mA
(2)
Peak Transient Input Current - I
F
(鈮?1
碌s
pulse width, 300 pps) . . . . . . . . . . . . . 1.0 A
Reverse Input Voltage - V
R
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 V
Input Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 mW
(3)
Average Output Current - I
O
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.0 mA
Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.0 mA
Emitter-Base Reverse Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 V
Supply and Output Voltage - V
CC
, V
O
. . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 15 V
Base Current - I
B
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 mA
Output Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mW
(4)
Caution:
This component is susceptible to damage from electrostatic discharge. Normal static
prevention procedures should be used in handling.
Notes:
(1) Derate linearly above 70
o
C free-air temperature at a rate of 0.45 mA/
o
C.
(2) Derate linearly above 70
o
C free-air temperature at a rate of 0.9 mA/
o
C.
(3) Derate linearly above 70
o
C free-air temperature at a rate of 0.8 mW/
o
C.
(4) Derate linearly above 70
o
C free-air temperature at a rate of 1.8 mW/
o
C.
(5) CM
H
is the maximum allowable dV/dt on the leading edge of a common mode pulse to
assure that the output will not switch from high to low.
(6) CM
L
is the maximum negative dV/dt allowable on the trailing edge of a common mode pulse
to assure that the output will not switch from low to high.
(7) Test conditions represents 1 TTL unit load with 5.6 k鈩?pull-up resistor.
(8) Test conditions represents 1 LSTTL unit load with a 6.1 k鈩?pull-up resistor.
(9) Device considered a two-terminal device: pins 2 and 3 shorted together and pins 5, 6, 7 and
8 shorted together.
Description
Optek鈥?HDC135 and HDC136 are high
s
speed optocouplers, consisting of IR
emitters and integrated photodetectors
in hermetic side brazed dual-in-line 8 pin
packages. Electrical characteristics are
similar to the 6N135 and 6N136
optocouplers but with full military
temperature range operation.
The HDC135B and HDC136B are high
reliability optocouplers with 100%
processing and Group Testing patterned
after MIL-STD-883 Method 5004 and
5005 for class B.
Typical screening and lot acceptance
tests are provided on page 13-4.
Minimum orders will apply to processed
devices.
Optek Technology, Inc.
1215 W. Crosby Road
Carrollton, Texas 75006
13-22
(214) 323-2200
Fax (214) 323-2396
1
2
