DATA SHEET
GBU10A~GBU10K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes
FEATURES
.310(7.90)
.290(7.40)
GBU
.880(22.3)
.860(21.8)
.160(4.1)
.140(3.5)
.080(2.03)
.060(1.52)
.740(18.8)
.720(18.3)
Unit: inch ( mm )
鈥?Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
鈥?Ideal for printed circuit board
鈥?Reliable low cost construction utilizing molded plastic technique
鈥?Surge overload rating: 200 Amperes peak
鈥?High temperature soldering guaranteed:
260擄C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
.140(3.56)
.130(3.30)
.085(2.16)
.065(1.65)
MECHANICAL DATA
Case: Reliable low cost construction utilizing
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
.100(2.54)
.085(2.16)
.080(2.03)
.065(1.65)
.190(4.83)
.210(5.33)
.075(1.90)R
.710(18.0)
.690(17.5)
.040(1.02)
.030(0.76)
.022(0.56)
.018(0.46)
.050(1.27)
.040(1.02)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25擄Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
GBU10A
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Input Voltage
Maximum DC Blocking Voltage
Maximum Average Forward T
C
=100擄C
Rectified Output Current at
I2t Rating for fusing ( t<8.35ms)
Peak Forward Surge Current single sine-wave superimposed on
rated load(JEDEC method)
Maximum Instantaneous Forward Voltage Drop per element at 5.0A
Maximum Reverse Leakage at rated T
A
=25擄
CDc Blocking Voltage per element T
C
=100擄C
Typical Thermal Resistance per leg(Note 2) R胃JA
Typical Thermal Resistance per leg(Note 3) R胃JC
Operating and Storage Temperature Range, T
J
,TSTG
50
35
50
GBU10B
100
70
100
GBU10D
200
140
200
10.0
GBU10G
400
280
400
GBU10J
600
420
600
GBU10K
800
560
800
UNIT
V
V
V
A
127
200
1.0
5.0
500
8.6
3.1
-55+150
A
2
sec
Apk
Vpk
碌A(chǔ)
碌A(chǔ)
擄C / W
擄C / W
擄C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
DATE : AUG.29.2002
PAGE . 1
1
2
