Approve Sheet
Part Number: GBJ6A~GBJ6K
DATA SHEET
GBJ6A~GBJ6K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 6.0 Amperes
GBJ
FEATURES
C 0.118 (3.0)
鈥?Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
鈥?Ideal for printed circuit board
鈥?Reliable low cost construction utilizing molded plastic technique
鈥?Surge overload rating: 175 Amperes peak
Unit: inch ( mm )
0.996(25.3)
0.972(24.7)
0.122(3.1)
0.142(3.6)
0.189(4.8)
0.173(4.4)
0.150(3.8)
0.133(3.4)
0.146(3.7)
0.129(3.3)
鈥?High temperature soldering guaranteed:
260擄C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
0.578(14.7)
0.603(15.3)
MECHANICAL DATA
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
0.087(2.2)
0.070(1.8)
0.044(1.1)
0.035(0.9)
0.304(7.7)
0.288(7.3)
0.669(17.0)
0.709(18.0)
Case: Reliable low cost construction utilizing
0.115(2.9)
0.098(2.5)
0.304(7.7)
0.288(7.3)
0.304(7.7)
0.288(7.3)
0.032(0.8)
0.024(0.6)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25擄Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
0.382(9.7)
0.366(9.3)
GBJ6A
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Input Voltage
Maximum DC Blocking Voltage
Maximum Average Forward T
C
=100擄C
Rectified Output Current
I
2
t Rating for fusing ( t<8.3ms)
Peak Forward Surge Current single sine-wave superimposed on rated load
(JEDEC method)
Maximum Instantaneous Forward Voltage Drop per element at 6.0A
Maximum Reverse Leakage at rated T
A
=25擄
CDc Blocking Voltage per element T
C
=100擄C
Typical Thermal Resistance per leg(Note 2) R胃JA
Typical Thermal Resistance per leg(Note 3) R胃JC
Operating and Storage Temperature Range, T
J
,TSTG
50
35
50
GBJ6B
100
70
100
GBJ6D
200
140
200
GBJ6G
400
280
400
6.0
GBJ6J
600
420
600
GBJ6K
800
560
800
UNIT
V
V
V
A
A
2
sec
127
175
1.0
5
500
8.6
3.1
-55 to +150
Apk
Vpk
碌A(chǔ)
碌A(chǔ)
擄C / W
擄C / W
擄C
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
PAGE . 1
1
2
