DATA SHEET
GBJ10A~GBJ10K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes
FEATURES
C 0.118 (3.0)
GBJ
0.996(25.3)
0.972(24.7)
Unit: inch ( mm )
鈥?Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
鈥?Ideal for printed circuit board
鈥?Reliable low cost construction utilizing molded plastic technique
鈥?Surge overload rating: 200 Amperes peak
0.189(4.8)
0.173(4.4)
0.122(3.1)
0.142(3.6)
0.150(3.8)
0.133(3.4)
0.146(3.7)
0.129(3.3)
鈥?High temperature soldering guaranteed:
260擄C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
0.578(14.7)
0.603(15.3)
MECHANICAL DATA
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Mounting position: Any
Mounting torque: 5 in. lb. Max.
Weight: 0.15 ounce, 4.0 grams
0.087(2.2)
0.070(1.8)
0.044(1.1)
0.035(0.9)
0.304(7.7)
0.288(7.3)
0.669(17.0)
0.709(18.0)
Case: Reliable low cost construction utilizing
0.115(2.9)
0.098(2.5)
0.304(7.7)
0.288(7.3)
0.304(7.7)
0.288(7.3)
0.032(0.8)
0.024(0.6)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25擄Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
GBJ10A
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Input Voltage
Maximum DC Blocking Voltage
Maximum Average Forward T
C
=100擄C
Rectified Output Current
T
A
= 45擄C
50
35
50
GBJ10B GBJ10D
100
70
100
200
140
200
GBJ10G
400
280
400
10.0
8.0
166
200
1.0
5
500
18.0
3.0
GBJ10J
600
420
600
0.382(9.7)
0.366(9.3)
GBJ10K
800
560
800
UNIT
V
V
V
A
A
2
sec
I
2
t Rating for fusing ( t<8.3ms)
Peak Forward Surge Current single sine-wave superimposed on rated load
(JEDEC method)
Maximum Instantaneous Forward Voltage Drop per element at 5.0A
Maximum Reverse Leakage at rated T
A
=25擄
CDc Blocking Voltage per element T
C
=100擄C
Typical Thermal Resistance per leg(Note 2) R胃JA
Typical Thermal Resistance per leg(Note 3) R胃JC
Operating and Storage Temperature Range, T
J
,TSTG
Apk
Vpk
碌A(chǔ)
碌A(chǔ)
擄C / W
擄C / W
擄C
-55 to +150
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 3.0 x 3.0" x 0.11" thick ( 7.5 x 7.5 x 0.3cm) AL plate.
DATE
: AUG.29.2002
PAGE . 1
1
2
