鈥?Pin compatible and functionally equivalent to ZBT鈩?/div>
devices
鈥?Internally self-timed output buffer control to eliminate
the need to use OE
鈥?Byte Write capability
鈥?128K x 36 common I/O architecture
鈥?Single 3.3V power supply
鈥?2.5V/3.3V I/O Operation
鈥?Fast clock-to-output times
鈥?2.6 ns (for 250-MHz device)
鈥?2.6 ns (for 225-MHz device)
鈥?2.8 ns (for 200-MHz device)
鈥?3.5 ns (for 166-MHz device)
鈥?4.0 ns (for 133-MHz device)
鈥?4.5 ns (for 100-MHz device)
鈥?Clock Enable (CEN) pin to suspend operation
鈥?Synchronous self-timed writes
鈥?Asynchronous output enable (OE)
鈥?JEDEC-standard 100 TQFP and 119 BGA packages
鈥?Burst Capability鈥攍inear or interleaved burst order
鈥?鈥淶Z鈥?Sleep mode option
Functional Description
[1]
The CY7C1350F is a 3.3V, 128K x 36 synchronous-pipelined
Burst SRAM designed specifically to support unlimited true
back-to-back Read/Write operations without the insertion of
wait states. The CY7C1350F is equipped with the advanced
No Bus Latency鈩?(NoBL鈩? logic required to enable consec-
utive Read/Write operations with data being transferred on
every clock cycle. This feature dramatically improves the
throughput of the SRAM, especially in systems that require
frequent Write/Read transitions.
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. All data outputs pass through
output registers controlled by the rising edge of the clock. The
clock input is qualified by the Clock Enable (CEN) signal,
which, when deasserted, suspends operation and extends the
previous clock cycle. Maximum access delay from the clock
rise is 2.8 ns (200-MHz device)
Write operations are controlled by the four Byte Write Select
(BW
[A:D]
) and a Write Enable (WE) input. All writes are
conducted with on-chip synchronous self-timed write circuitry.
Three synchronous Chip Enables (CE
1
, CE
2
, CE
3
) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output three-state control. In order to avoid bus
contention, the output drivers are synchronously three-stated
during the data portion of a write sequence.
.
Logic Block Diagram
A0, A1, A
MODE
CLK
CEN
ADDRESS
REGISTER 0
A1
A1'
D1
Q1
A0
A0'
BURST
D0
Q0
LOGIC
ADV/LD
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
C
ADV/LD
BW
A
BW
B
BW
C
BW
D
WE
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
WRITE
DRIVERS
MEMORY
ARRAY
S
E
N
S
E
A
M
P
S
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
D
A
T
A
S
T
E
E
R
I
N
G
O
U
T
P
U
T
B
U
F
F
E
R
S
E
DQs
DQP
A
DQP
B
DQP
C
DQP
D
E
INPUT
REGISTER 1
E
INPUT
REGISTER 0
E
OE
CE1
CE2
CE3
ZZ
READ LOGIC
SLEEP
CONTROL
Note:
1. For best-practices recommendations, please refer to the Cypress application note
System Design Guidelines
on www.cypress.com.
Cypress Semiconductor Corporation
Document #: 38-05305 Rev. *A
鈥?/div>
3901 North First Street
鈥?/div>
San Jose
,
CA 95134
鈥?/div>
408-943-2600
Revised January 19, 2004
next