HS-2100RH
Data Sheet
June 1999
File Number
4562.3
Radiation Hardened High Frequency
Half Bridge Driver
The Radiation Hardened HS-2100RH is a high frequency,
100V Half Bridge N-Channel MOSFET Driver IC, which is a
functional, pin-to-pin replacement for the Intersil HIP2500
and the industry standard 2110 types. The low-side and
high-side gate drivers are independently controlled. This
gives the user maximum 鏗俥xibility in dead-time selection and
driver protocol.
In addition, the device has on-chip error detection and
correction circuitry, which monitors the state of the high-side
latch and compares it to the HIN signal. If they disagree, a
set or reset pulse is generated to correct the high-side latch.
This feature protects the high-side latch from SEUs.
Undervoltage on the high-side supply forces HO low. When
that supply returns to a valid voltage, HO will go to the state
of HIN. Undervoltage on the low-side supply forces both LO
and HO low. When that supply becomes valid, LO returns to
the LIN state and HO returns to the HIN state.
Speci鏗乧ations for Rad Hard QML devices are controlled
by the Defense Supply Center in Columbus (DSCC). The
SMD numbers listed here must be used when ordering.
Detailed Electrical Speci鏗乧ations for the HS-2100RH are
contained in SMD 5962-99536. A 鈥渉ot-link鈥?is provided
on our homepage for downloading.
www.intersil.com/spacedefense/space.asp
This link will not be available until the SMD is 鏗乶alized.
Features
鈥?Electrically Screened to DESC SMD # 5962-99536
鈥?QML Quali鏗乪d per MIL-PRF-38535 Requirements
鈥?Radiation Environment
- Maximum Total Dose . . . . . . . . . . . . . . 3 x 10
5
RAD(SI)
- DI RSG Process Provides Latch-up Immunity
- Vertical Architecture Provides Low Dose Rate Immunity
鈥?Bootstrap Supply Max Voltage to 120V
鈥?Drives 1000pF Load at 1MHz with Rise and Fall Times of
45ns (Typ)
鈥?1A (Typ) Peak Output Current
鈥?Independent Inputs for Non-Half Bridge Topologies
鈥?Low DC Power Consumption . . . . . . . . . . . . . 60mW (Typ)
鈥?Operates with V
DD
= V
CC
Over 12V to 20V Range
鈥?Supply Undervoltage Protection
Applications
鈥?High Frequency Switch-Mode Power Supplies
鈥?Drivers for Inductive Loads
鈥?DC Motor Drivers
Pinout
HS-2100RH
FLATPACK (CDFP4-F16)
TOP VIEW
LO
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
NC
V
SS
LIN
SD
HIN
V
DD
NC
NC
Ordering Information
ORDERING NUMBER
5962F9953601VXC
5962F9953601QXC
HS9-2100RH/Proto
INTERSIL MKT.
NUMBER
HS9-2100RH-Q
HS9-2100RH-8
HS9-2100RH/Proto
TEMP.
RANGE (
o
C)
-55 to 125
-55 to 125
-55 to 125
COM
V
CC
NC
NC
VS
VB
HO
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143
|
Copyright
漏
Intersil Corporation 1999
INTERSIL
1
2
