2 Mbit / 3 Mbit / 4 Mbit / 8 Mbit Firmware Hub
SST49LF002A / SST49LF003A / SST49LF004A / SST49LF008A
SST49LF002A / 003A / 004A / 008A2 Mb / 3 Mb / 4 Mb / 8 Mb Firmware Hub for Intel 8xx Chipsets
Advance Information
FEATURES:
鈥?Firmware Hub for Intel 8xx Chipsets
鈥?2 Mbit, 3 Mbit, 4 Mbit, or 8 Mbit SuperFlash
memory array for code/data storage
鈥?SST49LF002A: 256K x8 (2 Mbit)
鈥?SST49LF003A: 384K x8 (3 Mbit)
鈥?SST49LF004A: 512K x8 (4 Mbit)
鈥?SST49LF008A: 1024K x8 (8 Mbit)
鈥?Flexible Erase Capability
鈥?Uniform 4 KByte Sectors
鈥?Uniform 16 KByte overlay blocks for
SST49LF002A
鈥?Uniform 64 KByte overlay blocks for
SST49LF003A/004A/008A
鈥?Top Boot Block protection
- 16 KByte for SST49LF002A
- 64 KByte for SST49LF003A/004A/008A
鈥?Chip-Erase for PP Mode Only
鈥?Single 3.0-3.6V Read and Write Operations
鈥?Superior Reliability
鈥?Endurance:100,000 Cycles (typical)
鈥?Greater than 100 years Data Retention
鈥?Low Power Consumption
鈥?Active Read Current: 6 mA (typical)
鈥?Standby Current: 10 碌A(chǔ) (typical)
鈥?Fast Sector-Erase/Byte-Program Operation
鈥?Sector-Erase Time: 18 ms (typical)
鈥?Block-Erase Time: 18 ms (typical)
鈥?Chip-Erase Time: 70 ms (typical)
鈥?Byte-Program Time: 14 碌s (typical)
鈥?Chip Rewrite Time:
SST49LF002A: 4 seconds (typical)
SST49LF003A: 6 seconds (typical)
SST49LF004A: 8 seconds (typical)
SST49LF008A: 15 seconds (typical)
鈥?Single-pulse Program or Erase
鈥?Internal timing generation
鈥?Two Operational Modes
鈥?Firmware Hub Interface (FWH) Mode for
in-system operation
鈥?Parallel Programming (PP) Mode for fast
production programming
鈥?Firmware Hub Hardware Interface Mode
鈥?5-signal communication interface supporting
byte Read and Write
鈥?33 MHz clock frequency operation
鈥?WP# and TBL# pins provide hardware write
protect for entire chip and/or top Boot Block
鈥?Block Locking Register for all blocks
鈥?Standard SDP Command Set
鈥?Data# Polling and Toggle Bit for End-of-Write
detection
鈥?5 GPI pins for system design flexibility
鈥?4 ID pins for multi-chip selection
鈥?Parallel Programming (PP) Mode
鈥?11-pin multiplexed address and
8-pin data I/O interface
鈥?Supports fast In-System or PROM programming
for manufacturing
鈥?CMOS and PCI I/O Compatibility
鈥?Packages Available
鈥?32-lead PLCC
鈥?32-lead TSOP (8mm x 14mm)
PRODUCT DESCRIPTION
The SST49LF00xA flash memory devices are designed
to be read-compatible with the Intel 82802 Firmware Hub
(FWH) device for PC-BIOS application. It provides pro-
tection for the storage and update of code and data in
addition to adding system design flexibility through five
general purpose inputs. Two interface modes are sup-
ported by the SST49LF00xA: Firmware Hub (FWH)
Interface Mode for In-System programming and Parallel
Programming (PP) Mode for fast factory programming of
PC-BIOS applications.
The SST49LF00xA flash memory devices are manufac-
tured with SST鈥檚 proprietary, high performance Super-
Flash Technology. The split-gate cell design and thick
oxide tunneling injector attain better reliability and manu-
facturability compared with alternate approaches. The
SST49LF00xA devices significantly improve performance
and reliability, while lowering power consumption. The
SST49LF00xA devices write (Program or Erase) with a
single 3.0-3.6V power supply. It uses less energy during
Erase and Program than alternative flash memory tech-
nologies. The total energy consumed is a function of the
applied voltage, current and time of application. Since for
漏2001 Silicon Storage Technology, Inc.
S71161-06-000 9/01
504
1
The SST logo and SuperFlash are registered trademarks of Silicon Storage Technology, Inc.
MPF is a trademark of Silicon Storage Technology, Inc. Intel is a registered trademark of Intel Corporation.
These specifications are subject to change without notice.