completion gages built in, including 120/1000 and 350鈩?/div>
dummies
鈥?Fully adjustable and
regulated
bridge excitation on each
channel up to 12Vdc by front panel control
鈥?Continuosly variable amplifier gain up to 2100 by front-
panel control
鈥?Separate bridge-power switch
鈥?Output 10Vdc at 100mA, short-circuit; proof and current
limiting standard
鈥?LED null indicators provided on each channel to
indicate amplifier and bridge-balance condition
鈥?High stability with temperature and time
鈥?Frequency response up to 50kHz
2120B REAR VIEW
DESCRIPTION
A two-channel plug-in amplifier module that includes bridge
completion, bridge balance, amplifier balance, bridge-exci-
tation regulator and shunt calibration.
SPECIFICATIONS
These specifications apply for each of two independent
channels per module.
Inputs:
Quarter (120鈩?1000鈩?and 350鈩?, half and full bridge
(50-1000鈩?. Quarter-bridge dummy gages provided.
Bridge Excitation:
0.5 to 12 Vdc (adjustable for each channel)
with 120鈩?full-bridge load.
Short-circuit current:
<40 mA.
Ripple, noise, and 10% line change:
鹵2
mV max.
Load regulation:
鹵0.2%
no-load to 120鈩?load (10% line
change).
Bridge Balance:
鹵2000碌蔚
(quarter, half, or 350鈩?full
bridge), range can be changed by internal jumper to
鹵4000碌蔚
or
鹵6000碌蔚.
Calibration:
Two-position (center off) toggle switch.
Standard factory-installed resistors (鹵0.1%) simulate
鹵1000碌蔚
at GF=2.
Amp Gain:
1 to 2100 continuously adjustable
鹵1%.
Bandpass:
DC to 5 kHz (min): 鈥?.5 dB (鈥?%).
DC to 15 kHz: 鈥? dB.
Can be extended by internal jumper to:
DC to 17 kHz: 鈥?.5 dB; DC to 50 kHz: 鈥? dB.
Amp Input:
Temperature Coefficient of Zero:
鹵1碌V/擄C
RTI (referred to input),
鹵210碌V/擄C
RTO
(referred to output); 鈥?0擄 to +60擄C (after 30 minute
warm-up).
Noise RTI:
(350鈩?source impedance)
1碌V p-p at 0.1 Hz to 10 Hz; 2碌V p-p at 0.1 Hz to 100 Hz;
2碌V at 0.1 Hz to 50 kHz.
Noise RTO:
50碌V p-p at 0.1 Hz to 10 Hz; 80碌V p-p at 0.1 Hz to
100 Hz; 100碌V at 0.1 Hz to 15 kHz; 200碌V at
0.1 Hz to 50 kHz.
Input Impedance:
>100M鈩?(balance limit resistor
disconnected).
Common-Mode Rejection:
(dc to 60 Hz).
Gain Multiplier
CMR (dB)
X2
67
X20
87
X200
100
Source Current:
鹵10
nA typical;
鹵40
nA max.
Output:
鹵10V
(min) at
鹵100
mA.
Current Limit:
140 mA.
Optional Feature:
May be ordered with, or be field upgraded for, remote-
operation relays for control of shunt calibration and bridge
excitation (off). Requires remote-operation capability in the
Model 2150 or 2160. Contact Vishay Micro-Measurements
for details.
Size:
5.25 H x 2.94 W x 10.97 D in (133 x 75 x 279 mm).
Weight:
2.2 lb (1.0 kg).
All Specifications are nominal or typical at + 23
擄
C unless
noted.
micro-measurements@vishay.com
www.vishaymg.com
1
Document Number: 11251
Revision 21-Nov-03
1
