|
|||||||||||
| 技術交流 | 電路欣賞 | 工控天地 | 數字廣電 | 通信技術 | 電源技術 | 測控之家 | EMC技術 | ARM技術 | EDA技術 | PCB技術 | 嵌入式系統 驅動編程 | 集成電路 | 器件替換 | 模擬技術 | 新手園地 | 單 片 機 | DSP技術 | MCU技術 | IC 設計 | IC 產業 | CAN-bus/DeviceNe |
電感測試 |
| 作者：ssqwq 欄目：技術交流 |
電極強度測試 NO TERMINAL DETACHMENT SHOULD BE FOUND WHEN THE DEVICE IS PUSHED IN TWO DIRECTIONS OF X AND Y WITH THE FORCE OF 5.0N FOR 10±2 SECONDS AFTER SOLDERING BETWEEN COPPER PLATE AND THE TERMINALS.(REFER TO FIGURE AT RIGHT) 將線圈的電極面與銅板焊接后，在X與Y方向 施加5.0N的靜加重10±2sec，電極面不會脫落 迴焊耐熱測試 絕緣測試 THE INSULATION RESISTANCE SHOULD BE OVER 100MΩ WHEN D.C.100V IS APPLIED TO THE WINDING –CORE. MEANWHILE NO STRUCTURE AND ELECTRIC DEFECTS SHOULD BE FOUND FOR 1 MINUTE. 在線圈和鐵芯上印加D.C. 100V絕緣電阻必須超過100MΩ，保持1min，沒有短路發生 溫度特性測試 NDUCTANCE COEFFICIENT IS (0～2000)x10-6(-25～+85℃) 電感的溫度系數為(0～2000)x10-6/℃(-25～+85℃) 濕度測試 NDUCTANCE DEVIATION IS WITHIN ±5.0% AND NO STRUCTURE AND ELECTRIC DEFECTS CAN BE FOUND AFTER 96 HOURS TEST UNDER THE CONDITIONOF RELATIVE HUMIDITY OF 90～95% AND TEMPERATURE OF 40±2℃. AND 1 HOUR STORAGE UNDER ROOM AMBIENT CONDITIONS AFTER THE DEVICE IS WIPED WITH DRY CLOTH. 相對濕度為90～95%，溫度為40±2℃的條件下放置96小時。將其擦干在室內環境下放置1小時，電感值變化在初始值±5.0%內，結構以及電氣特性沒有發生變化。 耐震測試 INDUCTANCE DEVIATION IS WITHIN ±5.0％ AFTER 1 HOUR SWEEPING VIBRATION IN EACH THREE DIRECTIONS. NAMELY, FREQUENCY IS 10～55～10Hz ANDTHE AMPLITUDE OF 1MINUTE CYCLE IS 1.5mm PP. 振動周波數10～55～10Hz，振幅1.5m/m在三個方向各保持一個小時，電感值變化在初始值±5.0%內 耐沖擊測試 INDUCTANCE DEVIATION IS WITHIN ±5.0% AFTER THE TEST WITH GOM-BLOCK SHOCK TESTING MACHINE,ONCE IN EACH OF THE THREE PERPENDICULAR AXIS DIRECTIONS. THE SHOCK ACCELERATION IS 981m/s2. 用GOM-BLOCK振動測試儀器在垂直的坐標軸方向測試，電感值變化在初始值±5.0%內。沖擊加速度為981m/s2 |
|
|
| 免費注冊為維庫電子開發網會員，參與電子工程師社區討論，點此進入 |
Copyright © 1998-2006 m.58mhw.cn 浙ICP證030469號 |