音影先锋亚洲天堂网|电影世界尽头的爱完整版播放|国产 熟女 91|高清无码免费观看欧美日韩|韩国一区二区三区黄色录像|美女亚洲加勒比在线|亚洲综合网 开心五月|7x成人在线入口|成人网站免费日韩毛片区|国产黄片?一级?二级?三级

LUCL9500AGF-D Datasheet

  • LUCL9500AGF-D

  • High-Voltage Ringing SLIC for VolP Applications

  • 32頁

  • AGERE

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

L9500A
High-Voltage Ringing SLIC for VoIP Applications
Preliminary Data Sheet
September 2001
Applications
(continued)
Power Ring
The device offers a ring mode, in which a balanced
power ring signal is provided to the tip/ring pair. During
the ring mode, a user-supplied low-voltage ring signal
is input to the device鈥檚 RING
IN
input. This signal is
amplified to produce the balanced power ring signal.
The user may supply a sine wave input, PWM input, or
a square wave to produce sinusoidal or trapezoidal
ringing at tip and ring.
Various crest factors are shown below for illustrative
purposes.
80
60
VOLTS (V)
40
20
0
鈥?0
鈥?0
鈥?0
鈥?0
0.00 0.04 0.08 0.12 0.16 0.20
0.02 0.06 0.10 0.14 0.18
TIME (s)
12-3346a (F)
Sine Wave Input Signal and Sine Wave Power Ring
Signal Output
The low-voltage sine wave input is applied differentially
or single ended to the L9500 at pins RING
INP
and
RING
INN
. During the ring mode, the signals at pins
RING
INP
and RING
INN
are amplified and presented to
the subscriber loop. The differential gain from RING
IN
to tip and ring is a nominal 70.
When the device enters the ring mode, the tip/ring
overhead set at OVH and the scan clamp circuit are
disabled, allowing the voltage magnitude of the power
ring signal to be maximized. Additionally, in the ring
mode, the loop current limit is increased 2.5X the value
set by the V
PROG
voltage.
The magnitude of the power ring voltage will be a func-
tion of the gain of the ring amplifier, the high-voltage
battery, and the input signal at RING
IN
. The input range
of the signal at RING
IN
is 0 V to Vcc. As the input volt-
age at RING
IN
is increased, the magnitude of the power
ring voltage at tip and ring will increase linearly, per the
gain of 70, until the tip and ring drive amplifiers begin to
saturate. Once the tip and ring amplifiers reach satura-
tion, further increases of the input signal will cause clip-
ping distortion of the power ring signal at tip and ring.
The ring signal will appear balanced on tip and ring.
That is, the power ring signal is applied to both tip and
ring, with the signal on tip 180擄 out of phase from the
signal on ring.
It is recommended that the input level at RING
IN
be
adjusted so that the power ring signal at tip and ring is
just at the edge or slightly clipping. This gives maxi-
mum power transfer with minimal distortion of the sine
wave. The tip side will saturate at a nominal 1 V above
ground. The ring side will saturate at a nominal 3 V
above battery. The input circuit for a sine wave along
with waveforms to illustrate the tip and ring saturation
is shown in Figure 9.
The point at which clipping of the power ring signal
begins at tip and ring is a function of the battery volt-
age, the input capacitor at RING
IN
, and the input signal
at RING
IN
and Vcc. During nonring modes, the sinusoi-
dal ringing waveform may be left on at RING
IN
. Via the
state table, the ring signal will be removed from tip and
ring even if the low-voltage input is still present at
RING
IN
.
Note: Slew rate = 5.65 V/ms; trise = tfall = 23 ms; pwidth = 2 ms;
period = 50 ms.
Figure 9. Ringing Waveform Crest Factor = 1.6
80
60
VOLTS (V)
40
20
0
鈥?0
鈥?0
鈥?0
鈥?0
0.00 0.04 0.08 0.12 0.16 0.20
0.02 0.06 0.10 0.14 0.18
TIME (s)
12-3347a (F)
Note: Slew rate = 10.83 V/ms; trise = tfall = 12 ms; pwidth = 13 ms;
period = 50 ms.
Figure 10. Ringing Waveform Crest Factor = 1.2
24
Agere Systems Inc.

LUCL9500AGF-D相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！