sProduct
Specifications
Nominal characteristic impedance
Rating
Rated frequency
DC-6GHz
Operating Relative Humidity
90% max.
50 ohms
Operating Temperature Range
-55莽
to +85莽
Item
01.
Insulation Resistance 500M ohms min.
Specification
500V DC
500V AC / 1 minute
100mA (DC or 1000Hz)
Condition
02.
Withstanding Voltage Neither short nor breakdown
03.
Contact Resistance
10m ohms max. (center),
05m
ohms max. (outer)
04.
Female Contact Retention 0.2N
to
2N
05.
Insertion and withdrawal
force (plug)
Insertion force: 15N max.
withdrawal force: 6
to
15N
1.2 max.
1.2 max. (MMCX-LR-SMT only)
1.4 max. (MMCX-LR-SMT only)
Measured with the
脴0.37
pin gauge.
Measured with an appropriate connector.
DC
to
6GHz
DC
to
4GHz
4GHz
to
6GHz
Measured at 0.45GHz
to
6GHz
Frequency: 10 to 500 Hz, single amplitude of 0.75 mm or
acceleration of 98 m/s
2
(peak), 2 hours in each of the 3 directions.
Acceleration of 735 m/s
2
, 6 ms duration, sine half-wave
waveform, 3 cycles in each of the 3 axis
06.
Voltage standing
wave ratio
07.
Vibration
No electrical discontinuity of 1碌s or more
No damage, cracks, or parts looseness.
No electrical discontinuity of 1碌s or more
No damage, cracks, or parts looseness.
No damage, cracks, or parts looseness.
Insulation resistance: 10M ohms min(High temperature)
Insulation resistance: 500M ohms min(Dry)
Contact resistance: 20m ohms max. (center)
08.
Shock
09.
Humidity
96 hours at temperature of 40莽 and humidity of 90% to 95%
Temperature of:
-55莽
鉃?/div>
+20
to
35莽
鉃?/div>
+85莽
Time: 30 minutes
5 cycles
500 cycles
Exposed to density 5% salt water for 48 hours
鉃?/div>
+20
to
35莽
10. Temperature Cycle
10m ohms max. (outer)
No damage, cracks, or parts looseness.
Contact resistance: 20m ohms max. (center)
10m ohms max. (outer)
鉃?
minutes max.
鉃?0
minutes
鉃?
minutes min.
11. Operating Life
12. Resistance to Corrosion No marked corrosion
*Voltage
standing wave ratio (V.S.W.R.) measuring system.
The above voltage standing wave ratio (V.S.W.R.) standard value is measured in the measuring system as shown below.
Network Analyzer
Test Set
Test Port
D.U.T
Test Post Cable
Termination
NOTE 1 : The cable connector is measured with double ended 15cm cable
assembly.
NOTE 2 : The PCB connector is mounted on the 50 ohms printed circuit
board, to which Hirose's adaptor is connected.
sMaterial
Parts
Body
Male center contact
Female center contact
Male/female in-line contact
Insulator
Fixing ring
Crimp sleeve
Cover
Material
Brass
Stainless steel (conversion adaptor)
Phosphor bronze
Beryllium bronze
Beryllium copper (conversion adaptor)
PTFE
Beryllium copper (plug)
Copper
Brass (plug)
Finish
Gold plating
Gold plating
Gold plating
Gold plating
鈥撯€?/div>
Gold plating
Gold plating
Gold plating
B32
1
2
3
4
5
6
7
8
