音影先锋亚洲天堂网|电影世界尽头的爱完整版播放|国产 熟女 91|高清无码免费观看欧美日韩|韩国一区二区三区黄色录像|美女亚洲加勒比在线|亚洲综合网 开心五月|7x成人在线入口|成人网站免费日韩毛片区|国产黄片?一级?二级?三级

MC3510 Datasheet

  • MC3510

  • ETC [Pilot Motion Processor]

  • ETC

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

6 Parallel Communication
With the addition of an external logic device, the Pilot motion processor can communicate with a
host processor using a parallel data stream. This offers a higher communication rate than a serial
interface and may be used in configurations where a serial connection is not available or not
convenient. This section details the required logic that must be implemented in the external device
as well as the necessary connections to the CP chip.
The reference design files for the parallel interface chip, in Actel/ViewLogic format, are available
from PMD. There are two versions of the design, one for interfacing with host processors that have
an 8-bit data bus and one for host processors that have a 16-bit data bus. The designs are called
IOPIL8 and IOPIL16 respectively. The interface to the CP chip is essentially identical in both.
The function of the I/O chip is to provide a shared-memory style interface between the host and CP
chip, comprised of four 16-bit wide locations. These are used for transferring commands and data
between the host and Pilot motion processor. The CP chip accesses the command/data registers
using its 16-bit external data bus while the host accesses the registers via a parallel interface with chip
select, read, write and command/data signals. If necessary, the host side interface can be modified
by the designer to match specific requirements of the host processor.
6.1
Host interface pin description table
Pin Name
HostCmd
Direction
input
output
Description
This signal is asserted
high
to write a host instruction to the motion processor, or to
read the status of the
HostRdy
and
HostIntrpt
signals. It is asserted
low
to read or write
a data word.
This signal is used to synchronize communication between the motion processor
and the host.
HostRdy
will go
low
(indicating host port busy) at the end of a read or
write operation according to the interface mode in use, as follows:
Interface Mode
HostRdy
goes low
8/16
after the second byte of the instruction word
after the second byte of each data word is transferred
16/16
after the 16-bit instruction word
after each 16-bit data word
serial
n/a
HostRdy
will go
high,
indicating that the host port is ready to transmit, when the last
transmission has been processed. All host port communications must be made
with
HostRdy
high
(ready).
A typical busy-to-ready cycle is 12.5 microseconds, but can be substantially longer,
up to 100 microseconds.
When
~HostRead
is
low,
a data word is read from the motion processor.
When
~HostWrite
is
low,
a data word is written to the motion processor.
When
~HostSlct
is
low,
the host port is selected for reading or writing operations.
I/O chip to CP chip interrupt. This signal sends an interrupt to the CP chip
whenever a host鈥揷hipset transmission occurs. It should be connected to CP chip
pin 53,
I/OIntrpt
.
This signal is
high
when the I/O chip is reading data from the I/O chip, and
low
when it is writing data. It should be connected to CP chip pin 4,
R/W
.
This signal goes
low
when the data and address become valid during Motion
processor communication with peripheral devices on the data bus, such as external
memory or a DAC. It should be connected to CP chip pin 6,
Strobe
.
MC3510 Technical Specifications
29
HostRdy
~HostRead
~HostWrite
~HostSlct
CPIntrpt
input
input
input
output
input
input
CPR/~W
CPStrobe

MC3510相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！