音影先锋亚洲天堂网|电影世界尽头的爱完整版播放|国产 熟女 91|高清无码免费观看欧美日韩|韩国一区二区三区黄色录像|美女亚洲加勒比在线|亚洲综合网 开心五月|7x成人在线入口|成人网站免费日韩毛片区|国产黄片?一级?二级?三级

LT1534C Datasheet

  • LT1534C

  • Linear Technology [Ultralow Noise 2A Switching Regulators]

  • LINER

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

LT1534/LT1534-1
PIN FUNCTIONS
(LT1534/LT1534-1)
COL (Pins 2, 15/Pin 2):
These two pins should be con-
nected together externally to create the collector of the
power switch. The emitter returns to PGND through a
sense resistor. Large currents flow into these pins so it is
desirable to keep external trace lengths short to minimize
radiation.
SYNC (Pin 4):
The SYNC pin can be used to synchronize
the oscillator to an external clock (see Oscillator Sync in
Applications Information section for more details). The
SYNC pin may either be floated or tied to ground if not
used.
C
T
(Pin 5):
The oscillator capacitor pin is used in
conjunction with R
T
to set the oscillator frequency.
For R
T
= 16.9k,
C
T(NF)
= 129/f
OSC(kHz)
R
T
(Pin 6):
The oscillator resistor pin is used to set the
charge and discharge currents of the oscillator capacitor.
The nominal value is 16.9k. It is possible to adjust this
resistance
鹵25%
to get a more accurate oscillator fre-
quency.
FB (Pin 7):
The feedback pin is used for positive voltage
sensing and oscillator frequency shifting during start-up
and short-circuit conditions. It is the inverting input to the
error amplifier. The noninverting input of this amplifier
connects internally to a 1.25V reference. This pin should
be left open if not used.
NFB (Pin 8/Pin 10):
The negative voltage feedback pin is
used for sensing a negative output voltage. The pin is
connected to the inverting input of the negative feedback
amplifier through a 100k source resistor. The negative
feedback amplifier provides a gain of 鈥?0.5 to the feedback
amplifier; therefore, the nominal regulation point is 鈥?2.5V
on NFB. This pin should be left open if not used.
GND (Pin 9/Pins 1, 8, 9, 16):
Signal Ground. The internal
error amplifier, negative feedback amplifier, oscillator,
slew control circuitry and the bandgap reference are
referred to this ground. Keep the connection to the feed-
back divider and V
C
compensation network free of large
ground currents.
V
C
(Pin 10/Pin 11):
The compensation pin is used for
frequency compensation and current limiting. It is the
output of the error amplifier and the input of the current
comparator. Loop frequency compensation can be per-
formed with an RC network connected from the V
C
pin to
ground.
SHDN (Pin 11/Pin 12):
The shutdown pin is used for
disabling the switcher. Grounding this pin will disable all
internal circuitry. Normally this output can be tied high (to
V
IN
) or may be left floating.
R
CSL
(Pin 12/Pin 13):
A resistor to ground sets the current
slew rate for the power switch. The minimum resistor
value is 3.9k and the maximum value is 68k. Current slew
will be approximately:
I
SLEW(A/碌s)
= 33/R
CSL(k鈩?
R
VSL
(Pin 13/Pin 14):
A resistor to ground sets the voltage
slew rate for the power switch collector. The minimum
resistor value is 3.9k and the maximum value is 68k.
Voltage slew will be approximately:
V
SLEW(V/碌s)
= 220/R
VSL(k鈩?
V
IN
(Pin 14/Pin 15):
Input Supply Pin. Bypass this pin with
a
鈮?/div>
4.7碌F low ESR capacitor. When V
IN
is below 2.55V the
part will go into undervoltage lockout where it will stop
output switching and pull the V
C
pin low.
PGND (Pin 16/Pin 3):
Power Switch Ground. This ground
comes from the emitters of the power switches. In normal
operation this pin should have approximately 25nH induc-
tance to ground. This can be done by trace inductance
(approximately 1") or with wire or a specific inductive
component (e.g., small ferrite bead). This inductance
ensures stability in the current slew control loop during
turn-off. Too much inductance (>50nH) may produce
oscillation on the output voltage slew edges.
6
U
U
U

LT1534C PDF文件相關型號

LT1534I

LT1534C相關型號PDF文件下載

  • 型號
    版本
    描述
    廠商
    下載
  • 英文版
    Seoul Semiconductor [Infrared LAMP LED]
    SEOUL
  • 英文版
    Adaptive-Frequency Current Mode Switching Regulators
    LINER
  • 英文版
    Adaptive-Frequency Current Mode Switching Regulators
    Linear
  • 英文版
    Adaptive-Frequency Current Mode Switching Regulators
    LINER
  • 英文版
    Adaptive-Frequency Current Mode Switching Regulators
    Linear
  • 英文版
    Constant-Current/Voltage High Efficiency Battery Charger
    LINER
  • 英文版
    Constant-Current/Voltage High Efficiency Battery Charger
    Linear
  • 英文版
    4.5A, 500kHz Step-Down Switching Regulator
    LINER
  • 英文版
    4.5A, 500kHz Step-Down Switching Regulator
    Linear
  • 英文版
    4.5A, 500kHz Step-Down Switching Regulator
    Linear
  • 英文版
    500kHz Monolithic Buck Mode Switching Regulator
    LINER
  • 英文版
    500kHz Monolithic Buck Mode Switching Regulator
    Linear
  • 英文版
    Power Factor and PWM Controller(Voltage Mode)
    LINER
  • 英文版
    Power Factor and PWM Controller (Voltage Mode)
    Linear
  • 英文版
    Power Factor and PWM Controller (Voltage Mode)
    Linear
  • 英文版
    Power Factor and PWM Controller
    LINER
  • 英文版
    Power Factor and PWM Controller
    Linear
  • 英文版
    3 Amp Positive Adjustable Regulator
    Linear
  • 英文版
    Seoul Semiconductor [GREEN OVAL LAMP LED]
    SEOUL
  • 英文版
    Constant-Voltage/ Constant-Current Battery Charger
    LINER

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！