音影先锋亚洲天堂网|电影世界尽头的爱完整版播放|国产 熟女 91|高清无码免费观看欧美日韩|韩国一区二区三区黄色录像|美女亚洲加勒比在线|亚洲综合网 开心五月|7x成人在线入口|成人网站免费日韩毛片区|国产黄片?一级?二级?三级

AD7934-6 Datasheet

  • AD7934-6

  • 4-Channel, 625 kSPS, 12-Bit Parallel ADC with a Sequencer

  • 1793.05KB

  • 30頁

  • AD

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

AD7934-6
Pin No.
21
22
23
Mnemonic
RD
CS
AGND
Description
Read Input. Active low logic input used in conjunction with CS to access the conversion result. The conversion
result is placed on the data bus following the falling edge of RD read while CS is low.
Chip Select. Active low logic input used in conjunction with RD and WR to read conversion data or write data
to the control register.
Analog Ground. This is the ground reference point for all analog circuitry on the AD7934-6. All analog input
signals and any external reference signal should be referred to this AGND voltage. The AGND and DGND
voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient
basis.
Reference Input/Output. This pin is connected to the internal reference, and is the reference source for the
ADC. The nominal internal reference voltage is 2.5 V, and it appears at this pin. It is recommended that this pin
be decoupled to AGND with a 470 nF capacitor. This pin can be overdriven by an external reference. The input
voltage range for the external reference is 0.1 V to V
DD
; however, care must be taken to ensure that the analog
input range does not exceed V
DD
+ 0.3 V. See the Reference Section.
Analog Input 0 to Analog Input 3. Four analog input channels that are multiplexed into the on-chip track-and-
hold. The analog inputs can be programmed to be four single-ended inputs, two fully differential pairs, or two
pseudo differential pairs by setting the MODE bits in the control register appropriately (see Table 9). The
analog input channel to be converted can be selected either by writing to the address bits (ADD1 and ADD0)
in the control register prior to the conversion, or by using the on-chip sequencer. The input range for all input
channels can be either 0 V to V
REF
, or 0 V to 2 脳 V
REF
, and the coding can be binary or twos complement,
depending on the states of the RANGE and CODING bits in the control register. Any unused input channels
should be connected to AGND to avoid noise pickup.
24
V
REFIN
/V
REFOUT
25 to 28
V
IN
0 to V
IN
3
Rev. A | Page 8 of 28

AD7934-6相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！