音影先锋亚洲天堂网|电影世界尽头的爱完整版播放|国产 熟女 91|高清无码免费观看欧美日韩|韩国一区二区三区黄色录像|美女亚洲加勒比在线|亚洲综合网 开心五月|7x成人在线入口|成人网站免费日韩毛片区|国产黄片?一级?二级?三级

AD7934-6 Datasheet

  • AD7934-6

  • 4-Channel, 625 kSPS, 12-Bit Parallel ADC with a Sequencer

  • 30頁

  • AD

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

AD7934-6
Reading Data from the AD7934-6
With the W/B pin tied logic high, the AD7934-6 interface
operates in word mode. In this case, a single read operation
from the device accesses the conversion data-word on Pins DB0
to DB11. The DB8/HBEN pin assumes its DB8 function. With
the W/B pin tied to logic low, the AD7934-6 interface operates
in byte mode. In this case, the DB8/HBEN pin assumes its
HBEN function.
Conversion data from the AD7934-6 must be accessed in two
read operations with 8 bits of data provided on DB0 to DB7 for
each of the read operations. The HBEN pin determines whether
the read operation accesses the high byte or the low byte of the
12-bit word. For a low byte read, DB0 to DB7 provide the eight
LSBs of the 12-bit word. For a high byte read, DB0 to DB3
provide the 4 MSBs of the 12-bit word. DB4 and DB5 of the
high byte provide the channel ID. DB6 and DB7 are always 0.
Figure 34 shows the read cycle timing diagram for a 12-bit
transfer. When operated in word mode, the HBEN input does
not exist and only the first read operation is required to access
data from the device. When operated in byte mode, the two
read cycles shown in Figure 35 are required to access the full
data-word from the device.
The CS and RD signals are gated internally and level triggered
active low. In either word mode or byte mode, CS and RD can
be tied together as the timing specification t
10
and t
11
are 0 ns
minimum. This means the bus is constantly driven by the
AD7934-6.
The data is placed onto the data bus a time, t
13
, after both CS
and RD go low. The RD rising edge can be used to latch data
out of the device. After a time, t
14
, the data lines become three-
stated.
Alternatively, CS and RD can be tied permanently low, and the
conversion data is valid and placed onto the data bus a time, t
9
,
before the falling edge of BUSY.
Note that if RD is pulsed during the conversion time then this
causes a degradation in linearity performance of approximately
0.25 LSB. Reading during conversion by way of tying CS and
RD low does not cause any degradation.
HBEN/DB8
t
15
CS
t
16
t
15
t
16
t
10
t
12
RD
t
11
t
17
DB0 TO DB7
LOW BYTE
HIGH BYTE
Figure 35. AD7934-6 Parallel Interface鈥擱ead Cycle Timing for Byte Mode Operation (W/B = 0)
Rev. A | Page 22 of 28
04752-005
t
13
t
14

AD7934-6相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！