音影先锋亚洲天堂网|电影世界尽头的爱完整版播放|国产 熟女 91|高清无码免费观看欧美日韩|韩国一区二区三区黄色录像|美女亚洲加勒比在线|亚洲综合网 开心五月|7x成人在线入口|成人网站免费日韩毛片区|国产黄片?一级?二级?三级

ADAU1702 Datasheet

  • ADAU1702

  • SigmaDSP? 28/56-Bit Audio Processor with 2ADC/4DAC

  • 38頁

  • AD

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

ADAU1702
SPI PORT
By default, the ADAU1702 is in I C mode, but can be put into SPI
control mode by pulling CLATCH/WP low three times. The SPI
port uses a 4-wire interface, consisting of CLATCH, CCLK,
CDATA, and COUT signals and is always a slave port. The
CLATCH signal should go low at the beginning of a transaction
and high at the end of a transaction. The CCLK signal latches
CDATA on a low-to-high transition. COUT data is shifted out of
the ADAU1702 on the falling edge of CCLK and should be
clocked into a receiving device, such as a microcontroller, on the
CCLK rising edge. The CDATA signal carries the serial input
data, and the COUT signal is the serial output data. The COUT
signal remains three-stated until a read operation is requested.
This allows other SPI-compatible peripherals to share the same
readback line. All SPI transactions have the same basic format
shown in Table 18. A timing diagram is shown in Figure 4. All
data should be written MSB first. The ADAU1702 cannot be
taken out of SPI mode without a full reset.
2
Table 17. ADAU1702 SPI Address Byte Format
Bit 0
0
Bit 1
0
Bit 2
0
Bit 3
0
Bit 4
0
Bit 5
0
Bit 6
ADDR0
Bit 7
R/W
Subaddress
The 12-bit subaddress word is decoded into a location in one of
the memories or registers. This subaddress is the location of the
appropriate RAM location or register. The MSBs of the subaddress
are zero-padded to bring the word to a full 2-byte length.
Data Bytes
The number of data bytes varies according to the register or
memory being accessed. During a burst mode write, an initial
subaddress is written followed by a continuous sequence of data
for consecutive memory/register locations. The detailed data
format for continuous mode operation is shown in Table 23 and
Table 25 in the Read/Write Data Formats section.
A sample timing diagram for a single-write SPI operation to the
parameter RAM is shown in Figure 26. A sample timing diagram
of a single-read SPI operation is shown in Figure 27. The COUT
pin goes from three-state to being driven at the beginning of
Byte 3. In this example, Byte 0 to Byte 2 contain the addresses
and R/W bit and subsequent bytes carry the data.
Chip Address R/W
The first byte of an SPI transaction includes the 7-bit chip address
and a R/W bit. The chip address is set by the ADDR0 pin. This
allows two ADAU1702s to share a CLATCH signal, yet still operate
independently. When ADDR0 is low, the chip address is 0000000;
when it is high, the address is 0000001 (see Table 17). The LSB
of this first byte determines whether the SPI transaction is a
read (Logic Level 1) or a write (Logic Level 0).
Table 18. Generic Control Word Format
Byte 0
chip_adr [6:0], R/W
1
Byte 1
0000, subadr [11:8]
Byte 2
subadr [7:0]
Byte 3
data
Byte 4
1
data
Continues to end of data.
CLATCH
CCLK
CDATA
BYTE 0
BYTE 1
BYTE 2
BYTE 3
Figure 26. SPI Write to ADAU1702 Clocking (Single-Write Mode)
CLATCH
CCLK
CDATA
BYTE 0
BYTE 1
COUT
HI-Z
DATA
DATA
DATA
HI-Z
Figure 27. SPI Read from ADAU1702 Clocking (Single-Read Mode)
Rev. 0 | Page 25 of 52
05798-015
05798-014

ADAU1702相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！