TEMPERATURE RANGE (REF. TO25擄C)
SETTABILITY AT Vfo 鈥?/div>
CONTROL VOLTAGE RANGE
LINEARITY
SYMMETRY
SLOPE
MODULATION FREQUENCY BANDWIDTH 10 KHz (-3dB) MIN
INPUT IMPEDANCE
ABSOLUTE VOLTAGE RANGE
ENABLE/DISABLE FUNCTION
PHASE NOISE (TYPICAL)
10 KOHM MIN
-0.5 TO +7.0 VDC FOR VCC AND VC (NON DESTRUCTIVE)
CONTROL PIN 2: HIGH OR OPEN (+2.O VDC MIN) OUTPUT PIN 4: ENABLED
CONTROL PIN 2: LOW OR GND (+0.8 VDC MAX) OUTPUT PIN 4: DISABLED (HIGH Z)
SEE GRAPH FOR PHASE NOISE CHARACTERISTICS
鈥?Vfo IS THE CONTROL VOLTAGE AT WHICH THE OUTPUT FREQUENCY IS EQUAL TO THE NOMINAL FREQUENCY Fo
AT 25 C
ABSOLUTE PULL RANGE (APR) IS THE MINIMUM GUARANTEED FREQUENCY SHIFT FROM Fo OVER VARIATIONS IN
TEMPERATURE, AGING, POWER SUPPLY, AND LOAD.
TEMPERATURE RANGE DESIGNATIONS
TABLE 1
CODE
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
TEMPERATURE
RANGE
0擄C TO +50擄C
0擄C TO +50擄C
0擄C TO +50擄C
0擄C TO +50擄C
0擄C TO +50擄C
0擄C TO +50擄C
0擄C TO +70擄C
0擄C TO +70擄C
0擄C TO +70擄C
0擄C TO +70擄C
0擄C TO +70擄C
0擄C TO +70擄C
-40擄C TO +85擄C
-40擄C TO +85擄C
-40擄C TO +85擄C
-40擄C TO +85擄C
-40擄C TO +85擄C
TEMPERATURE
STABILITY
鹵 10 PPM
鹵 15 PPM
鹵 15 PPM
鹵 20 PPM
鹵 25 PPM
鹵 35 PPM
鹵 10 PPM
鹵 20 PPM
鹵 20 PPM
鹵 25 PPM
鹵 35 PPM
鹵 50 PPM
鹵 20 PPM
鹵 30 PPM
鹵 25 PPM
鹵 35 PPM
鹵 50 PPM
APR
鹵 50 PPM
鹵 50 PPM
鹵 50 PPM
鹵 75 PPM
鹵 75 PPM
鹵 100PPM
鹵 50 PPM
鹵 50 PPM
鹵 50 PPM
鹵 50 PPM
鹵 75 PPM
鹵 100 PPM
鹵 50 PPM
鹵 50 PPM
鹵 75 PPM
鹵 75 PPM
鹵 100 PPM
OUTPUT AND LOAD CHARACTERISTICS
TABLE 2
TTL/HCMOS COMPATIBLE
SYMMETRY: 40/60% TO 60/40% AT +1.4 VDC
TTL - 3 GATES (VC/VE81) VOH: +2.4 VDC MIN
VOL: +0.4 VDC MAX
RISE/FALL TIME: 10 ns WITH STANDARD LOAD (20% TO 80%)
TTL/HCMOS COMPATIBLE
SYMMETRY: 40/60% TO 60/40% AT 50% LEVEL
HCMOS - 15 pF (VC/VE82) VOH: +4.5 VDC MIN
VOL: +0.5 VDC MAX
RISE/FALL TIME: 5 ns WITH STANDARD LOAD (20% TO 80%)
ACMOS TO DRIVE 3 GATES AT TTL LEVELS
SYMMETRY: 40/60% TO 60/40% AT 50% LEVEL
ACMOS - 30 pF (VC/VE83) VOH: +4.5 VDC MIN
VOL: +0.5 VDC MAX
RISE/FALL TIME: 5 ns WITH 30 pF LOAD (20% TO 80%)
MECHANICAL CHARACTERISTICS
MECHANICAL SHOCK
THERMAL SHOCK
RANDOM VIBRATION
GROSS LEAK
HERMETIC SEAL
SOLDERING CONDITIONS
MECHANICAL
MIL-STD-202, METHID 213, CONDITION E
MIL-STD-883, METHOD 1011, CONDITION A
MIL-STD-883, METHOD 2007, CONDITION A
100% LEAK TESTED IN DEIONIZED WATER
LEAK RATE LESS THAN 0.05 PPM ATM x cc/s OF HELIUM
240擄 C 鹵5 s MAXIMUM FOR 10 s
SURFACE MOUNT, 6 PIN PER OUTLINE DRAWING
Powered by ICminer.com Electronic-Library Service CopyRight 2003
Raltron Electronics Corporation 10651 NW 19th St. Miami, Florida 33172 U.S.A.
Tel: 305-593-6033 Fax: 305-594-3973 e-mail: sales@raltron.com Internet: http://www.raltron.com
1
2
