CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CF
Chip Type, Standard
series
Ultra Low ESR, High ripple current.
Load life of 2000 hours at 105擄C.
SMD type : Lead free reflow soldering condition at 260擄C peak
correspondence.
Adapted to the RoHS directive (2002/95/EC).
Specifications
Item
Category Temperature Range
Rated Voltage Range
Performance Characteristics
鈥?55 ~ +105擄C
2.5 ~ 25V
鹵 20% at 120Hz, 20擄C
Not more than value of Standard ratings at 120Hz, 20擄C
Not more than value of Standard ratings at 100kHz, 20擄C
Rated Capacitance Range
6.8 ~ 1500碌F
Capacitance Tolerance
tan
未
ESR (
1)
2)
Leakage Current (
Not more than value of Standard ratings.
Z+105擄C / Z+20擄C
Z鈥?55擄C / Z+20擄C
1.25
1.25
(100kHz)
After 2 minute's application of rated voltage.
20擄C
Characteristics of Temperature
Impedance Ratio
Endurance
After 2000 hours' application of rated voltage
at 105擄C, capacitors meet the specified value
for life characteristics listed at right.
Capacitance change
tan
未
ESR
( 1)
Leakage current ( 2)
Capacitance change
tan
未
ESR
( 1)
Leakage current ( 2)
Within 鹵 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
Within 鹵 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
Damp Heat
After 1000 hours' application of rated voltage
at 60擄C 90%RH, capacitors meet the specified value
for life characteristics listed at right.
To comply with recommended conditions for
reflow soldering. Pre-heating shall be done
at 150 ~ 200擄C and for 60 ~ 180 sec.
In the case of peak temp, less than 250擄C,
reflow soldering shall be within two times.
In the case of peak temp, less than 260擄C,
reflow soldering shall be once.
Measurement for solder temperature profile shall
be made at the capacitor top and the terminal.
Navy blue print on the case top
Resistance to
Soldering Heat
Capacitance change
tan
未
ESR
( 1)
Leakage current ( 2)
Within 鹵 10% of initial value ( 3)
130% or less of the initial specified value
130% or less of the initial specified value
Initial specified value or less
Marking
1 ESR measurements should be made at a point on the terminal nearest where the terminals protrude through the plastic platform.
2 Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the
temperature of 105擄C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Type numbering system (Example : 6.3V 150碌F)
C鹵0.2
0.5 MAX.
Negative
A鹵0.2
Voltage
V
Code
2.5
e
4
g
6.3
j
10
A
16
C
20
D
25
E
Lot No.
B
D + 0.5 MAX.
Plastic platform
0.3 MAX.
Positive
CF
150
j
6X1
B鹵0.2
Series
Voltage
( j:6.3v)
L
+0.1
-0.4
H
(mm)
Size
蠁D
L
A
B
C
E
H
蠁6.3
脳
6L
6.3
5.9
7.3
6.6
6.6
2.1
0.5 ~ 0.8
蠁8
脳
7L
8.0
6.9
9.0
8.3
8.3
3.2
0.8 ~ 1.1
蠁10
脳
8L
10.0
7.9
11.0
10.3
10.3
4.6
0.8 ~ 1.1
蠁10
脳
10L
10.0
9.9
11.0
10.3
10.3
4.6
0.8 ~ 1.1
Dimension table in next page.
E
CAT.8100V
NICHICON
1
2
