音影先锋亚洲天堂网|电影世界尽头的爱完整版播放|国产 熟女 91|高清无码免费观看欧美日韩|韩国一区二区三区黄色录像|美女亚洲加勒比在线|亚洲综合网 开心五月|7x成人在线入口|成人网站免费日韩毛片区|国产黄片?一级?二级?三级

A29002T-120 Datasheet

  • A29002T-120

  • 256K X 8 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory

  • 32頁

  • AMICC

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

A29002/A290021 Series
256K X 8 Bit CMOS 5.0 Volt-only,
Boot Sector Flash Memory
Features
n
5.0V
鹵
10% for read and write operations
n
Access times:
- 55/70/90/120/150 (max.)
n
Current:
- 20 mA typical active read current
- 30 mA typical program/erase current
- 1
碌A(chǔ)
typical CMOS standby
n
Flexible sector architecture
-
16 Kbyte/ 8 KbyteX2/ 32 Kbyte/ 64 KbyteX3 sectors
-
Any combination of sectors can be erased
-
Supports full chip erase
-
Sector protection:
A hardware method of protecting sectors to prevent
any inadvertent program or erase operations within
that sector
n
Top or bottom boot block configurations available
n
Embedded Erase Algorithms
- Embedded Erase algorithm will automatically erase
the entire chip or any combination of designated
sectors and verify the erased sectors
- Embedded Program algorithm automatically writes
and verifies bytes at specified addresses
n
Typical 100,000 program/erase cycles per sector
n
20-year data retention at 125擄C
- Reliable operation for the life of the system
n
Compatible with JEDEC-standards
- Pinout and software compatible with single-power-
supply Flash memory standard
-
Superior inadvertent write protection
n
Data
Polling and toggle bits
-
Provides a software method of detecting completion
of program or erase operations
n
Erase Suspend/Erase Resume
-
Suspends a sector erase operation to read data
from, or program data to, a non-erasing sector, then
resumes the erase operation
n
Hardware reset pin (
RESET
)
-
Hardware method to reset the device to reading array
data (not available on A290021)
n
Package options
-
32-pin P-DIP, PLCC, or TSOP (Forward type)
General Description
The A29002 is a 5.0 volt-only Flash memory organized as
262,144 bytes of 8 bits each. The A29002 offers the
RESET
function, but it is not available on A290021. The 256 Kbytes
of data are further divided into seven sectors for flexible
sector erase capability. The 8 bits of data appear on I/O
0
-
I/O
7
while the addresses are input on A0 to A17. The A29002
is offered in 32-pin PLCC, TSOP, and PDIP packages. This
device is designed to be programmed in-system with the
standard system 5.0 volt VCC supply. Additional 12.0 volt
VPP is not required for in-system write or erase operations.
However, the A29002 can also be programmed in standard
EPROM programmers.
The A29002 has the first toggle bit, I/O
6
, which indicates
whether an Embedded Program or Erase is in progress, or it
is in the Erase Suspend. Besides the I/O
6
toggle bit, the
A29002 has a second toggle bit, I/O
2
, to indicate whether the
addressed sector is being selected for erase. The A29002
also offers the ability to program in the Erase Suspend mode.
The standard A29002 offers access times of 55, 70, 90, 120,
and 150 ns, allowing high-speed microprocessors to operate
without wait states. To eliminate bus contention the device
has separate chip enable (
CE
), write enable (
WE
) and
output enable (
OE
) controls.
The device requires only a single 5.0 volt power supply for both
read and write functions. Internally generated and regulated
voltages are provided for the program and erase operations.
The A29002 is entirely software command set compatible with
the JEDEC single-power-supply Flash standard. Commands
are written to the command register using standard
microprocessor write timings. Register contents serve as input
to an internal state-machine that controls the erase and
programming circuitry. Write cycles also internally latch
addresses and data needed for the programming and erase
operations. Reading data out of the device is similar to reading
from other Flash or EPROM devices.
Device programming occurs by writing the proper program
command sequence. This initiates the Embedded Program
algorithm - an internal algorithm that automatically times the
program pulse widths and verifies proper program margin.
Device erasure occurs by executing the proper erase command
sequence. This initiates the Embedded Erase algorithm - an
internal algorithm that automatically preprograms the array (if it
is not already programmed) before executing the erase
operation. During erase, the device automatically times the
erase pulse widths and verifies proper erase margin.
(February, 2002, Version 1.0)
1
AMIC Technology, Inc.

A29002T-120相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！