音影先锋亚洲天堂网|电影世界尽头的爱完整版播放|国产 熟女 91|高清无码免费观看欧美日韩|韩国一区二区三区黄色录像|美女亚洲加勒比在线|亚洲综合网 开心五月|7x成人在线入口|成人网站免费日韩毛片区|国产黄片?一级?二级?三级

A29001U-55 Datasheet

  • A29001U-55

  • 128K X 8 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory

  • 312.95KB

  • 32頁

  • AMICC

掃碼查看芯片數據手冊

上傳產品規格書

PDF預覽

A29001/290011 Series
128K X 8 Bit CMOS 5.0 Volt-only,
Preliminary
Features
n
5.0V
鹵
10% for read and write operations
n
Access times:
- 55/70/90 (max.)
n
Current:
- 20 mA typical active read current
- 30 mA typical program/erase current
- 1
碌A(chǔ)
typical CMOS standby
n
Flexible sector architecture
-
8 Kbyte/ 4 KbyteX2/ 16 Kbyte/ 32 KbyteX3 sectors
-
Any combination of sectors can be erased
-
Supports full chip erase
-
Sector protection:
A hardware method of protecting sectors to prevent
any inadvertent program or erase operations within
that sector
n
Top or bottom boot block configurations available
n
Embedded Erase Algorithms
- Embedded Erase algorithm will automatically erase the
entire chip or any combination of designated sectors
and verify the erased sectors
- Embedded Program algorithm automatically writes and
verifies bytes at specified addresses
n
Typical 100,000 program/erase cycles per sector
n
20-year data retention at 125擄C
- Reliable operation for the life of the system
n
Compatible with JEDEC-standards
- Pinout and software compatible with single-power-
supply Flash memory standard
-
Superior inadvertent write protection
n
Data
Polling and toggle bits
-
Provides a software method of detecting completion of
program or erase operations
n
Erase Suspend/Erase Resume
-
Suspends a sector erase operation to read data from,
or program data to, a non-erasing sector, then
resumes the erase operation
n
Hardware reset pin (
RESET
)
-
Hardware method to reset the device to reading array
data (not available on A290011)
n
Package options
-
32-pin P-DIP, PLCC, or TSOP (Forward type)
Boot Sector Flash Memory
General Description
The A29001 is a 5.0 volt-only Flash memory organized as
131,072 bytes of 8 bits each. The A29001 offers the
RESET
function, but it is not available on A290011. The 128 Kbytes of
data are further divided into seven sectors for flexible sector
erase capability. The 8 bits of data appear on I/O
0
- I/O
7
while
the addresses are input on A0 to A16. The A29001 is offered in
32-pin PLCC, TSOP, and PDIP packages. This device is
designed to be programmed in-system with the standard
system 5.0 volt VCC supply. Additional 12.0 volt VPP is not
required for in-system write or erase operations. However, the
A29001 can also be programmed in standard EPROM
programmers.
The A29001 has the first toggle bit, I/O
6
, which indicates
whether an Embedded Program or Erase is in progress, or it is
in the Erase Suspend. Besides the I/O
6
toggle bit, the A29001
has a second toggle bit, I/O
2
, to indicate whether the
addressed sector is being selected for erase. The A29001 also
offers the ability to program in the Erase Suspend mode. The
standard A29001 offers access times of 55, 70 and 90 ns
allowing high-speed microprocessors to operate without wait
states. To eliminate bus contention the device has separate
chip enable (
CE
), write enable (
WE
) and output enable (
OE
)
controls.
The device requires only a single 5.0 volt power supply for both
read and write functions. Internally generated and regulated
voltages are provided for the program and erase operations.
The A29001 is entirely software command set compatible with
the JEDEC single-power-supply Flash standard. Commands
are written to the command register using standard
microprocessor write timings. Register contents serve as input
to an internal state-machine that controls the erase and
programming circuitry. Write cycles also internally latch
addresses and data needed for the programming and erase
operations. Reading data out of the device is similar to reading
from other Flash or EPROM devices.
Device programming occurs by writing the proper program
command sequence. This initiates the Embedded Program
algorithm - an internal algorithm that automatically times the
program pulse widths and verifies proper program margin.
Device erasure occurs by executing the proper erase
command sequence. This initiates the Embedded Erase
algorithm - an internal algorithm that automatically
preprograms the array (if it is not already programmed) before
executing the erase operation. During erase, the device
automatically times the erase pulse widths and verifies proper
erase margin.
PRELIMINARY
(August, 2001, Version 0.3)
1
AMIC Technology, Inc.

A29001U-55相關型號PDF文件下載

您可能感興趣的PDF文件資料

熱門IC型號推薦

掃碼下載APP，
一鍵連接廣大的電子世界。

在線人工客服

買家服務：
賣家服務：
技術客服：

0571-85317607

網站技術支持

13606545031

客服在線時間周一至周五
9:00-17:30

關注官方微信號，
第一時間獲取資訊。

建議反饋
返回頂部

建議反饋

聯系人：

聯系方式：

按住滑塊，拖拽到最右邊
>>
感謝您向阿庫提出的寶貴意見，您的參與是維庫提升服務的動力！意見一經采納，將有感恩紅包奉上哦！